Cisco 300-610 Daily Practice Exam New 2023 Updated 172 Questions
Use Valid 300-610 Exam - Actual Exam Question & Answer
NEW QUESTION 72
Which orchestration tool should be used for the management and analytics of servers across multiple sites?
- A. Cisco Intersight
- B. Cisco Data Center Network Manager
- C. Cisco UCS Manager
- D. Cisco Nexus Fabric Manager
Answer: A
NEW QUESTION 73
An engineer designs a Cisco UCS solution that must provide guaranteed and deterministic bandwidth to a specific server in the environment. The solution must apply to network and storage traffic of C-Series and B-Series servers. Which solution should be included to meet these requirements?
- A. Pin the vNICs and the vHBAs of the service profile to dedicated uplink ports.
- B. Pin the IOM ports of the service profile to dedicated server ports.
- C. Pin the server ports of the service profile to dedicates uplink ports.
- D. Pin the vNlCs and vHBAs of the service profile to dedicated server ports
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-2/b_UCSM_GUI_Configuration_Guide_2_2/b_UCSM_GUI_Configuration_Guide_2_2_chapter_010.html#concept_7DE33CE2E37A47C6992C012D51CA37D4
NEW QUESTION 74
Drag and drop the configurations from the left onto the correct policies on the right.
Answer:
Explanation:
NEW QUESTION 75
Which orchestration tool provides a graphical interface to manage LAN and SAN fabrics?
- A. Cisco Data Center Network Manager
- B. Cisco CloudCenter
- C. Cisco Nexus Fabric Manager
- D. Cisco Virtual Topology System
Answer: A
Explanation:
Section: Automation Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/DCNM_OLH/SAN_Client/fmhelp/ fmc.html#34479
NEW QUESTION 76
Which two automation requirements can be met by using Puppet? (Choose two.)
- A. Enable clients to pull changes without installing an agent.
- B. Enable clients to pull changes to configuration files.
- C. Push configuration updates immediately to servers.
- D. Provide support for writing new modules in Python.
- E. Enable one-off infrastructure changes to be performed manually.
Answer: B,C
NEW QUESTION 77
A company has added a new FCoE storage array to increase the performance of datastore access for end users. This storage array is directly connected to the Cisco Nexus 5672UP switches using four 10G port-channel interfaces. After deployment, the end users fail to access the datastore compared to the older solution. A network engineer verified the port-channel interface and finds that the congestion occurs when PFC frames are generated at the FCoE ingress interface. Which action must be taken to resolve the congestion issue?
- A. Increase the queuing buffer in the port-channel interface connected to the storage array.
- B. Reserve bandwidth for FCoE VLAN on the port-channel interface connected with storage.
- C. Add an additional FCoE VLAN to the SAN network.
- D. Enable the FCoE class in QoS on Cisco Nexus 5672UP switches.
Answer: A
NEW QUESTION 78
A customer needs to deploy a three-tier network architecture that will consist of web, app, and other businesscritical applications. The solution will include Cisco UCS 6324 Fabric Interconnects managing B and C series servers. The fabric interconnects will be connected to the Cisco Nexus 7706 Series Switch for network access.
A storage array will be directly connected to the UCS fabric interconnects.
Which UCS deployment type must be used to meet these requirements?
- A. UCS interconnect in Ethernet end-host mode
UCS interconnect in Fibre Channel end-host mode
Fabric Interconnects uplinked to the Nexus device using an LACP port-channel in passive mode - B. UCS interconnect in Ethernet end-host mode
UCS interconnect in Fibre Channel switching mode
Fabric Interconnects uplinked to the Nexus device using an LACP port-channel in active mode - C. UCS interconnect in Ethernet switching mode
UCS interconnect in Fibre Channel end-host mode
Fabric Interconnects uplinked to the Nexus device using an LACP port-channel in active mode - D. UCS interconnect in Ethernet switching mode
UCS interconnect in Fibre Channel switching mode
Fabric Interconnects uplinked to the Nexus device using an LACP port-channel in passive mode
Answer: C
NEW QUESTION 79
Which authentication software natively runs within the CLI of Cisco NX-OS devices?
- A. Chef
- B. Puppet
- C. Python
- D. Ansible
Answer: D
NEW QUESTION 80
Which two configurations allow for routing traffic between two VDCs? (Choose two.)
- A. Create a policy map in the default VDC that routes traffic between the VDCs.
- B. Create VRF-aware software infrastructure interfaces.
- C. Cross-connect the ports between the VDCs.
- D. Create interfaces in the VDC that can be accessed by another VDC.
- E. Connect the VDCs to an external Layer 3 device.
Answer: A,E
NEW QUESTION 81
What is a design consideration when implementing FSPF?
- A. Routes are based on the domain ID.
- B. Routes are based on the distance vector protocol.
- C. FSPF runs only on F Ports.
- D. FSPF runs on a per-chassis basis.
Answer: A
Explanation:
Section: Network Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/5_0/configuration/guides/ fabric/nxos/cli_fabric/fspf.html
NEW QUESTION 82
When planning to deploy a load-balancing service as a managed node, which ACI configuration must be included?
- A. BGP ECMP
- B. ITD
- C. inline load-balancing device
- D. Layer 4 to Layer 7 device package
Answer: D
NEW QUESTION 83
What are two reasons to select OTV as the DCI solution to connect multisite topologies? (Choose two.)
- A. Layer 3 failures do not propagate beyond the OTV edge device.
- B. It constrains HSRP hello messages to each data center.
- C. It propagates hosts reachability without support of traffic flooding.
- D. It extends the spanning tree between data centers.
- E. It is an open standard.
Answer: A,D
NEW QUESTION 84
A network engineer must create a Fibre Channel fabric QoS design for an existing data center. The solution must provide relative bandwidth guarantees to application traffic, control latency, and prioritize application traffic.
Which mechanism must be deployed to support these requirements?
- A. traffic shaping
- B. traffic classification
- C. traffic policing
- D. traffic remarking
Answer: A
NEW QUESTION 85
Drag and drop the technologies from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION 86
Refer to the exhibit.
An engineer must assign multiple Fibre Channel IDs to a single port channel. Which two features must be enabled this goal? (Choose two.)
- A. NPIV feature on the Cisco MDS Series
- B. NPV feature on the Cisco MDS Series.
- C. Smart Zoning feature on the Cisco UCS Fabric Interconnects
- D. SAN Pin Groups on the Cisco UCS Fabric Interconnects.
- E. end-host mode feature on the Cisco UCS Fabric Interconnects
Answer: A,B
NEW QUESTION 87
Drag and drop the technologies from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION 88
An engineer configured the OSPF protocol in the vPC topology. During the catastrophic failure of one of the vPC the member switches, the traffic was routed to a black hole. This route was caused by the long convergence time caused by the delay of the of the vPC member switch reboot. After the failure, the engineer rebooted both switches, but the secondary switch powered on before the primary one. It caused all the vPCs to be shut down due to consistency-check violations. Which two features must be used to prevent these situations from happening in the future? (Choose two.)
- A. auto-recovery
- B. system priority
- C. ip arp synchronize
- D. peer-gateway
- E. delay restore
Answer: A,E
Explanation:
System priority is related to LACP, not vPC, so it is out. ARP s
Reference:
https://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/nx-os-software/212589-understanding-vpc-election-process.html
NEW QUESTION 89
A client in a commercial building Installs a Cisco blade server in the multitenant Cisco UCS blade Infrastructure. To cut operating costs me client's data center is shared with other organizations. The client asks an engineer prevent third parties from accessing their equipment and from accessing BlOS-related information when booting a server. Which Two policies must be used to meet these requirements? (Choose two.)
- A. post error pause
- B. ASPM support
- C. quiet boot
- D. CDN control
- E. front panel lockout
Answer: C,D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Server-Mgmt/3-2/b_Cisco_UCS_Manager_Server_Mgmt_Guide_3_2/b_Cisco_UCS_Manager_Server_Mgmt_Guide_3_2_chapter_01110.html Quiet boot is what the BIOS displays during booting the server. If enabled, the BIOS displays the logo screen.
I believe that quiet boot and CDN control may have the customer name.
NEW QUESTION 90
An engineer configured the OSPF protocol in the vPC topology. During the catastrophic failure of one of the vPC the member switches, the traffic was routed to a black hole. This route was caused by the long convergence time caused by the delay of the of the vPC member switch reboot. After the failure, the engineer rebooted both switches, but the secondary switch powered on before the primary one. It caused all the vPCs to be shut down due to consistency-check violations. Which two features must be used to prevent these situations from happening in the future? (Choose two.)
- A. auto-recovery
- B. system priority
- C. ip arp synchronize
- D. peer-gateway
- E. delay restore
Answer: A,E
Explanation:
System priority is related to LACP, not vPC, so it is out. ARP s
https://www.cisco.com/c/en/us/support/docs/switches/nexus-7000-series-switches/116187-configure-vpc-00.html
https://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/nx-os-software/212589-understanding-vpc-election-process.html
NEW QUESTION 91
An engineer must configure an interface for managing and orchestrating a Cisco Nexus device. The interface must be operational if the data and control planes crash, support IPv4 and IPv6 addressing, and have access to its own VRF instance.
Which interface should be used to meet these requirements?
- A. interface VLAN
- B. management interface
- C. physical interface
- D. loopback interface
Answer: B
NEW QUESTION 92
Refer to the exhibit.
What must be the default gateway of the servers in EPG Web?
- A. subnet address of BD1
- B. NAT appliance
- C. subnet address of L3Out
- D. subnet address of BD2
Answer: B
NEW QUESTION 93
An engineer must use OTV for layer 2 connectivity between data centers to support virtual machine between the customer sites. To support this requirement, the engineer must ensure the existence of the same default gateway on both sites. Additionally, the operations team report high bandwidth utilization on site A and wants to optimize the outbound traffic flows to use a DC exit point. Which feature must be used to meet these requirement?
- A. Control group
- B. FHRP filter
- C. Data group
- D. ARP filter
Answer: B
Explanation:
https://www.cisco.com/c/dam/en/us/products/collateral/switches/nexus-7000-series-switches/guide_c07-728315.pdf
NEW QUESTION 94
Refer to the exhibit.
A Cisco UCS chassis that has two IOMs is discovered. The chassis discovery policy creates a fabric port channel. What is the result of this policy?
- A. The port channel is disabled until an administrator enables it manually.
- B. Cisco UCS Manager creates a single fabric port channel.
- C. Cisco UCS Manager creates two separate fabric port channels.
- D. Each uplink that connects an IOM is configured as a discrete link.
Answer: C
NEW QUESTION 95
Which pools are used when a vNIC template is created in Cisco UCS Manager?
- A. MAC
- B. UUID
- C. WWPN
- D. IP
Answer: A
NEW QUESTION 96
Which factor determines the choice of platform designing a Cisco HyperFlex infrastructure to support computer-aided design applications?
- A. GPU support
- B. processor count
- C. network speed
- D. storage capacity
Answer: D
Explanation:
Section: Storage Network Design
NEW QUESTION 97
......
Test Engine to Practice 300-610 Test Questions: https://exam-hub.prepawayexam.com/Cisco/braindumps.300-610.ete.file.html